User Tools
Site Tools
equipment:3dprinting:ultimaker
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
| equipment:3dprinting:ultimaker [2018/03/11 19:10] – [Print setting] Anders Vestergaard | equipment:3dprinting:ultimaker [2018/03/15 18:13] – Anders Vestergaard | ||
|---|---|---|---|
| Line 13: | Line 13: | ||
| **NYE BILLEDER PÅ VEJ** | **NYE BILLEDER PÅ VEJ** | ||
| - | {{: | + | {{: |
| + | {{: | ||
| + | |||
| ===== Print setting ===== | ===== Print setting ===== | ||
| Line 29: | Line 32: | ||
| ==== Start gcode ==== | ==== Start gcode ==== | ||
| + | < | ||
| G21 ;metric values | G21 ;metric values | ||
| - | |||
| G90 ;absolute positioning | G90 ;absolute positioning | ||
| - | |||
| M82 ;set extruder to absolute mode | M82 ;set extruder to absolute mode | ||
| - | |||
| M107 ; | M107 ; | ||
| - | |||
| G28 Z0 ;move Z to min endstops | G28 Z0 ;move Z to min endstops | ||
| - | |||
| G28 X0 Y0 ;move X/Y to min endstops | G28 X0 Y0 ;move X/Y to min endstops | ||
| - | |||
| G1 X10 Y10 Z15.0 F1000 ;move the platform down 15mm | G1 X10 Y10 Z15.0 F1000 ;move the platform down 15mm | ||
| - | |||
| G92 E0 ;zero the extruded length | G92 E0 ;zero the extruded length | ||
| - | |||
| G1 F200 E3 ;extrude 3mm of feed stock | G1 F200 E3 ;extrude 3mm of feed stock | ||
| - | |||
| G92 E0 ;zero the extruded length again | G92 E0 ;zero the extruded length again | ||
| - | |||
| ;Put printing message on LCD screen | ;Put printing message on LCD screen | ||
| - | |||
| M117 Printing... | M117 Printing... | ||
| + | </ | ||
| ==== Stop gcode ==== | ==== Stop gcode ==== | ||
| + | < | ||
| ;End GCode | ;End GCode | ||
| M104 S0 ; | M104 S0 ; | ||
| - | |||
| M140 S0 ; | M140 S0 ; | ||
| - | |||
| G91 ;relative positioning | G91 ;relative positioning | ||
| - | |||
| G1 E-2 F300 ;retract the filament a bit before lifting the nozzle to release some of the pressure | G1 E-2 F300 ;retract the filament a bit before lifting the nozzle to release some of the pressure | ||
| - | |||
| G1 Z+0.5 E-3 X-20 Y-20 F1000 ;move Z up a bit and retract filament even more | G1 Z+0.5 E-3 X-20 Y-20 F1000 ;move Z up a bit and retract filament even more | ||
| - | |||
| G28 X0 Y0 ;move X/Y to min endstops | G28 X0 Y0 ;move X/Y to min endstops | ||
| - | |||
| G28 Z0 ;move Z to min endstops so the head is out of the way | G28 Z0 ;move Z to min endstops so the head is out of the way | ||
| - | |||
| M84 ; | M84 ; | ||
| - | |||
| M107 ;Turn fan off | M107 ;Turn fan off | ||
| - | |||
| G90 ; | G90 ; | ||
| + | </ | ||
| ===== Betjening af Ultimaker ===== | ===== Betjening af Ultimaker ===== | ||
Permalink equipment/3dprinting/ultimaker.txt · Last modified: 2018/03/15 18:13 by Anders Vestergaard
oeffentlich
