Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| equipment:3dprinting:ultimaker [2018/03/11 19:12] – [Stop gcode] Anders Vestergaard | equipment:3dprinting:ultimaker [2024/08/22 19:35] (current) – Solgt Torsten Martinsen | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Ultimaker ====== | ||
| - | |||
| - | ^ QR-ID | HQR1012 | | ||
| - | ^ Navn | Ultimaker | | ||
| - | ^ Kort beskr. | ||
| - | ^ Indehaver | ||
| - | ^ Tilladt brug | Use allowed. Hvis du ikke har prøvet at bruge en 3D-printer før, så spørg en erfaren bruger (på [[infrastruktur: | ||
| - | ^ Brug af 3dprinter | ||
| - | |||
| - | Printeren er blevet renoveret den 11/3 2018 af [[members: | ||
| - | |||
| - | |||
| - | **NYE BILLEDER PÅ VEJ** | ||
| - | |||
| - | {{: | ||
| - | |||
| - | ===== Print setting ===== | ||
| - | |||
| - | Her er listet de optimale indstillinger. | ||
| - | |||
| - | |||
| - | ^ Layerhight: | ||
| - | ^ Print speed:| 60 mm/s | | ||
| - | ^ Filament:| 1,75 mm | | ||
| - | ^ Nozzle:| 0,4 mm | | ||
| - | ^ Print areal:| 190x190x170, | ||
| - | ^ Retraction: | ||
| - | ^ Retraction speed:| 60 mm/s | | ||
| - | |||
| - | ==== Start gcode ==== | ||
| - | < | ||
| - | G21 ;metric values | ||
| - | G90 ;absolute positioning | ||
| - | M82 ;set extruder to absolute mode | ||
| - | M107 ; | ||
| - | G28 Z0 ;move Z to min endstops | ||
| - | G28 X0 Y0 ;move X/Y to min endstops | ||
| - | G1 X10 Y10 Z15.0 F1000 ;move the platform down 15mm | ||
| - | G92 E0 ;zero the extruded length | ||
| - | G1 F200 E3 ;extrude 3mm of feed stock | ||
| - | G92 E0 ;zero the extruded length again | ||
| - | ;Put printing message on LCD screen | ||
| - | M117 Printing... | ||
| - | </ | ||
| - | ==== Stop gcode ==== | ||
| - | < | ||
| - | ;End GCode | ||
| - | M104 S0 ; | ||
| - | M140 S0 ; | ||
| - | G91 ;relative positioning | ||
| - | G1 E-2 F300 ;retract the filament a bit before lifting the nozzle to release some of the pressure | ||
| - | G1 Z+0.5 E-3 X-20 Y-20 F1000 ;move Z up a bit and retract filament even more | ||
| - | G28 X0 Y0 ;move X/Y to min endstops | ||
| - | G28 Z0 ;move Z to min endstops so the head is out of the way | ||
| - | M84 ; | ||
| - | M107 ;Turn fan off | ||
| - | G90 ; | ||
| - | </ | ||
| - | ===== Betjening af Ultimaker ===== | ||
| - | |||
| - | Tænd printeren på ON-OFF knappen på højre side af printeren. | ||
| - | |||
| - | {{: | ||
| - | |||
| - | Indsæt SD kort med GCode i siden af displayet. | ||
| - | |||
| - | Tryk drejeknappen ind så menuen kommer op hvor "Print from SD ->" vælges: | ||
| - | |||
| - | {{: | ||
| - | |||
| - | Der efter vælges din gcode fil: | ||
| - | |||
| - | {{: | ||
| - | |||
| - | Nu varmer printeren op og starter derefter printet: | ||
| - | |||
| - | {{: | ||
| - | |||
| - | ==== Firmware ==== | ||
| - | |||
| - | https:// | ||